โJan-09-2019 12:49 PM
โMay-25-2019 10:24 AM
โMay-24-2019 06:53 PM
GHop wrote:RollandB wrote:GHop wrote:
I think I ordered the wrong one. Where did you guys take your measurements from? I went by an Rv web site which said to measure from center wheel hug to center wheel hug which measured on my rig 35inches so I purchased the SRE2 735x. After going on MorRyde I found they wanted you to measure from one hanger to the second hanger so for my rig it was 59inches.
Hub to hub centers should work, or the centers of the axles would do the same. Should be either 33 or 35โ. Iโve seen the MorRyde site with the page of measuring the hangers. I found that isnโt truly accurate as Northwood who makes our fifth wheel has different axle spacing but I have 35โ axle centers.
If you are measuring I would also compare the three holes in the CRE3000. On the one I had for a 35โ centers caused the axles to be nearly 33โ as the dimensions of the three holes was different than the OEM equalizers. In Talking to MorRyde they were stumped on the issue the CRE3000 caused (which isnโt a problem on the SRE4000.
Thank you for responding. I measured the Dexter equalizer and you have six inches and the two center of the mounting holes on the SRE 4000 is 8 inches. After measuring all of this I called MorRyde and was told I should have ordered the SRE 733.
โApr-18-2019 05:51 PM
sayoung wrote:
I didn't realize how much difference between my 3000's that came on our 5er and the 4000. Our rig also came with the shock mounts but with the axles flipped no body has been able to get me a shock that fits. Not Jayco or LCI, Monroe won't give me a clue either.
Did you do both 4000 & Joyrider at same time ?
โApr-18-2019 11:49 AM
โApr-17-2019 01:33 PM
โJan-26-2019 08:53 AM
RollandB wrote:
GHop, did you measure the hub or Axle centers? Reason I ask is I would go more with that measurement.
Ours was 35โ with the OEM Dexter equalizer, the CRE3000 that I had put on ours before the SRE4000 was a 35โ but moved the spacing to 33โ. Thatโs when I got in touch with Dexter, emailed photos as I was concerned with the change since it brought the tires closer to each other. They involved one of there engineers and couldnโt explain the change they also said I would have 33โ based on the hanger spacing.
I installed the 35โ SRE4000 and got the spacing back to about 35โ as it was before.
If you donโt have wet bolts now, I would suggest getting them with the SRE4000
Good luck with your install!
โJan-26-2019 06:19 AM
โJan-25-2019 08:18 AM
RollandB wrote:GHop wrote:
I think I ordered the wrong one. Where did you guys take your measurements from? I went by an Rv web site which said to measure from center wheel hug to center wheel hug which measured on my rig 35inches so I purchased the SRE2 735x. After going on MorRyde I found they wanted you to measure from one hanger to the second hanger so for my rig it was 59inches.
Hub to hub centers should work, or the centers of the axles would do the same. Should be either 33 or 35โ. Iโve seen the MorRyde site with the page of measuring the hangers. I found that isnโt truly accurate as Northwood who makes our fifth wheel has different axle spacing but I have 35โ axle centers.
If you are measuring I would also compare the three holes in the CRE3000. On the one I had for a 35โ centers caused the axles to be nearly 33โ as the dimensions of the three holes was different than the OEM equalizers. In Talking to MorRyde they were stumped on the issue the CRE3000 caused (which isnโt a problem on the SRE4000.
โJan-25-2019 05:23 AM
GHop wrote:
I think I ordered the wrong one. Where did you guys take your measurements from? I went by an Rv web site which said to measure from center wheel hug to center wheel hug which measured on my rig 35inches so I purchased the SRE2 735x. After going on MorRyde I found they wanted you to measure from one hanger to the second hanger so for my rig it was 59inches.
โJan-24-2019 03:12 PM
โJan-21-2019 08:42 AM
โJan-20-2019 11:57 AM
โJan-13-2019 10:33 AM
โJan-13-2019 07:34 AM
jaycocamprs wrote:sayoung wrote:
I didn't realize how much difference between my 3000's that came on our 5er and the 4000. Our rig also came with the shock mounts but with the axles flipped no body has been able to get me a shock that fits. Not Jayco or LCI, Monroe won't give me a clue either.
Did you do both 4000 & Joyrider at same time ?
Monroe 555001 Compressed Length 7.875" Extended Length 11.875" Travel Length 4.000"
Monroe 555026 Compressed Length 8.625" Extended Length 13.500" Travel Length 4.875"
Both are Stem Mount, with rubber bushings.